STIHL MS 200 T Onderdelen
Onderdeelnummers, configuraties en compatibiliteit
Voor de STIHL MS 200 T bevat de catalogus 201 bekende onderdelen en 2 gedocumenteerde secties. Controleer altijd uitvoering en onderdeelnummer voordat u bestelt.
π§ Veelgezochte Onderhouds- & Slijtagedelen Canonieke Selectie
STIHL MS 200 TGedocumenteerde onderdelen voor regulier onderhoud en periodieke vervanging op de STIHL MS 200 T.
Canonieke Onderdelencatalogus 201 onderdelen
Onderdelen ingedeeld volgens officiΓ«le diagramsecties en documentatiereeksen.
Unresolved Diagram Section
200 onderdelen| Pos. | Onderdeelnummer | Omschrijving | Aantal |
|---|---|---|---|
| 9 | 0000 121 4700 | Metering Diaphragm | 1 |
| 29 | 0000 190 3409 | Starter Grip Elastostart 3Mm | 1 |
| 31 | 0000 195 7001 | Cap | 1 |
| 30 | 0000 195 8205 | Starter Rope 3 X 750Mm | 1 |
| 8 | 0000 350 0533 | Oil Tank Cap | 1 |
| 13 | 0000 350 0537 | Oil Filler Cap | 1 |
| 7 | 0000 350 3500 | Brandstoffilter / zuigkop | 1 |
| 8 | 0000 350 5802 | Tank Vent | 1 |
| 3 | 0000 400 1306 | Ontstekingsmodule | 1 |
| 4 | 0000 930 2251 | Ignition Lead 10M | 1 |
| 9 | 0000 930 2803 | Hose 3.1X5.7 Mm X 1 M, R3 | 1 |
| 15 | 0000 955 0801 | Nut | 1 |
| 2 | 0000 955 0802 | Collar Nut | 1 |
| 4 | 0000 958 0407 | Washer | 1 |
| 27 | 0000 958 0923 | Washer | 1 |
| 32 | 0000 967 7247 | Warning Pictogram Ms | 1 |
| 4 | 0000 988 5211 | Connector | 1 |
| 14 | 0000 989 0810 | Grommet | 1 |
| 13 | 0000 989 0812 | Grommet | 1 |
| 29 | 0000 989 0813 | Grommet | 1 |
| 28 | 0000 989 0814 | Grommet | 1 |
| 5 | 0000 997 0617 | Helical Spring | 1 |
| 12 | 0000 997 1018 | Helical Spring | 1 |
| 27 | 0000 997 5515 | Tension Spring | 1 |
| 16 | 0000 998 0603 | Torsion Spring | 1 |
| 15 | 1106 405 1000 | High Tension Lead Connector | 1 |
| 21 | 1110 084 9102 | Bushing | 1 |
| 3 | 1110 353 1600 | Fuel Tank Vent Valve | 1 |
| 17 | 1110 400 7005 | Spark plug Bosch WSR6F | 1 |
| 10 | 1113 141 1805 | Sleeve | 1 |
| 24 | 1114 034 3001 | Compression Ring | 1 |
| 15 | 1116 790 9600 | Annular Buffer | 1 |
| 28 | 1118 195 3500 | Spring Starter Pawl Clip | 1 |
| 22 | 1120 034 1501 | Piston Pin 9X5X23 | 1 |
| 17 | 1120 036 8500 | Woodruff Key 2X3.7 | 1 |
| 6 | 1120 121 9200 | Spindle | 1 |
| 23 | 1120 122 3005 | Spring | 1 |
| 7 | 1120 122 6600 | Kraagschroef | 1 |
| 11 | 1120 122 6601 | Kraagschroef | 1 |
| 29 | 1120 122 7400 | Round Head Screw | 1 |
| 17 | 1120 122 7800 | Oval Head Screw | 1 |
| 2 | 1120 162 5200 | Pin | 1 |
| 26 | 1121 162 3000 | Support | 1 |
| 3 | 1123 121 0700 | Cup Plug | 1 |
| 15 | 1123 121 0800 | End Cover | 1 |
| 21 | 1123 121 3300 | Throttle Shutter | 1 |
| 12 | 1123 121 7800 | Strainer | 1 |
| 18 | 1123 122 3000 | Spring | 1 |
| 27 | 1123 122 3200 | Torsion Spring | 1 |
| 23 | 1123 122 3203 | Torsion Spring | 1 |
| 17 | 1123 122 6200 | Idle Speed Screw | 1 |
| 14 | 1123 129 0905 | Pakking | 1 |
| 10 | 1123 160 5400 | Brake Band | 1 |
| 23 | 1123 190 0600 | Rewind Spring | 1 |
| 25 | 1123 195 0400 | Rope Rotor | 1 |
| 12 | 1123 640 3800 | Brandstoffilter / zuigkop | 1 |
| 14 | 1123 648 6600 | Bumper Strip | 1 |
| 30 | 1123 664 1400 | Thrust Pad | 1 |
| 31 | 1123 664 2200 | Cover | 1 |
| 5 | 1125 121 5000 | Inlet Control Lever | 1 |
| 3 | 1125 122 4200 | Ball | 1 |
| 4 | 1125 122 6600 | Kraagschroef | 1 |
| 31 | 1125 122 7403 | Round Head Screw | 1 |
| 21 | 1125 122 9001 | E-Clip | 1 |
| 24 | 1125 122 9002 | E-Clip | 1 |
| 26 | 1125 195 7200 | Pawl MS170 MS180 MS210 MS230 MS250 Chainsaw Parts | 1 |
| 4 | 1128 122 3000 | Spring | 1 |
| 9 | 1128 160 5000 | Lever | 1 |
| 7 | 1128 640 9100 | Valve | 1 |
| 6 | 1128 647 4806 | Control Bolt | 1 |
| 28 | 1129 007 1000 | Spur Gear / Chain Adjusting Screw Kit | 1 |
| 13 | 1129 007 1050 | Set Of Gaskets | 1 |
| 34 | 1129 007 1062 | Set Of Carburettor Parts | 1 |
| 12 | 1129 020 1150 | Cover | 1 |
| 6 | 1129 020 2903 | Crankcase Sprocket Side | 1 |
| 15 | 1129 029 0500 | Pakking | 1 |
| 19 | 1129 029 2303 | Cylinder Gasket | 1 |
| 16 | 1129 030 0400 | Krukas | 1 |
| 21 | 1129 030 2002 | Piston 40Mm | 1 |
| 20 | 1129 080 1806 | Fan Housing | 1 |
| 19 | 1129 080 2105 | Fan Housing With Rewind Starter | 1 |
| 32 | 1129 084 7800 | Segment | 1 |
| 1 | 1129 120 0650 | Carburettor C1Q-S32B | 1 |
| 5 | 1129 120 0654 | Carburettor C1Q-S127D | 1 |
| 1 | 1129 120 1603 | Luchtfilter | 1 |
| 34 | 1129 120 7102 | Throttle Shaft With Lever | 1 |
| 19 | 1129 120 7103 | Throttle Shaft With Lever | 1 |
| 22 | 1129 120 7201 | Choke Shaft With Lever | 1 |
| 33 | 1129 120 9701 | Pump Piston Kit | 1 |
| 32 | 1129 120 9702 | Pump Piston Kit | 1 |
| 25 | 1129 121 2701 | Cap | 1 |
| 28 | 1129 121 2900 | Choke Shutter | 1 |
| 20 | 1129 121 3301 | Throttle Shutter | 1 |
| 13 | 1129 121 4800 | Pump Diaphragm | 1 |
| 2 | 1129 121 5400 | Valve Jet | 1 |
| 2 | 1129 121 5406 | Valve Jet | 1 |
| 11 | 1129 121 8600 | Washer | 1 |
| 26 | 1129 122 6701 | High Speed Screw | 1 |
| 24 | 1129 122 6702 | High Speed Screw | 1 |
| 25 | 1129 122 6801 | Low Speed Screw | 1 |
| 23 | 1129 122 6802 | Low Speed Screw | 1 |
| 37 | 1129 123 7505 | Grommet | 1 |
| 7 | 1129 123 7509 | Grommet | 1 |
| 2 | 1129 124 3400 | Filter Base | 1 |
| 8 | 1129 129 0900 | Pakking | 1 |
| 28 | 1129 140 0602 | Uitlaat | 1 |
| 3 | 1129 140 1903 | Carburettor Box Cover | 1 |
| 12 | 1129 141 2201 | Manifold | 1 |
| 4 | 1129 141 2300 | Twist Lock | 1 |
| 13 | 1129 141 3300 | Supporting Plate | 1 |
| 27 | 1129 149 0600 | Muffler Gasket | 1 |
| 24 | 1129 160 2000 | Koppeling | 1 |
| 25 | 1129 162 0800 | Clutch Shoe | 1 |
| 6 | 1129 162 6600 | Limit Stop | 1 |
| 11 | 1129 162 7800 | Flat Spring | 1 |
| 7 | 1129 180 1501 | Throttle Trigger | 1 |
| 9 | 1129 182 0801 | Trigger Interlock | 1 |
| 5 | 1129 182 0901 | Switch Shaft | 1 |
| 10 | 1129 182 1502 | Throttle Rod | 1 |
| 8 | 1129 182 4500 | Torsion Spring | 1 |
| 11 | 1129 185 1902 | [NO LONGER AVAILABLE] Stihl Choke Rod | 1 |
| 12 | 1129 185 2001 | Choke Lever | 1 |
| 24 | 1129 190 0601 | Rewind Spring | 1 |
| 1 | 1129 350 0807 | Tankbehuizing | 1 |
| 1 | 1129 350 0851 | Tankbehuizing | 1 |
| 5 | 1129 350 3601 | Hose | 1 |
| 2 | 1129 351 3000 | Reflector Foil | 1 |
| 3 | 1129 351 4000 | Insulating Plate | 1 |
| 4 | 1129 352 5500 | Clamp | 1 |
| 4 | 1129 353 2000 | Filter | 1 |
| 6 | 1129 358 1902 | Connector | 1 |
| 11 | 1129 358 7701 | Hose | 1 |
| 1 | 1129 400 1201 | Vliegwiel | 1 |
| 7 | 1129 440 1100 | Short Circuit Wire | 1 |
| 25 | 1129 440 3000 | Wiring Harness | 1 |
| 6 | 1129 442 1600 | Contactveer | 1 |
| 29 | 1129 640 1900 | Tensioner Slide | 1 |
| 19 | 1129 640 2000 | Chain Sprocket 3/8'' Picco 6T | 1 |
| 22 | 1129 640 2004 | Chain Sprocket 0.325'' 7T | 1 |
| 20 | 1129 640 2050 | Set Of Spur Sprocket/Worm 3/8" Picco 7T | 1 |
| 21 | 1129 640 2051 | Set Of Spur Sprocket/Worm 1/4'' 8T | 1 |
| 2 | 1129 640 3000 | Pump Housing | 1 |
| 1 | 1129 640 3200 | Oliepomp | 1 |
| 3 | 1129 640 5000 | Insert | 1 |
| 13 | 1129 640 7100 | Worm 3/8'' Picco 6T | 1 |
| 14 | 1129 640 7101 | Worm Picco 7T | 1 |
| 15 | 1129 640 7102 | Worm 1/4'' 8T | 1 |
| 16 | 1129 640 7105 | Worm .325" | 1 |
| 3 | 1129 647 0600 | Pump Piston | 1 |
| 10 | 1129 647 5701 | Connector | 1 |
| 9 | 1129 647 7000 | Plug | 1 |
| 11 | 1129 647 9400 | Hose | 1 |
| 13 | 1129 648 7700 | Cover | 1 |
| 5 | 1129 656 7701 | Chain Catcher | 1 |
| 31 | 1129 664 0500 | Bumper Spike | 1 |
| 10 | 1129 664 2400 | Kraagschroef | 1 |
| 9 | 1129 664 2401 | Collar Screw M8 | 1 |
| 2 | 1129 790 1013 | Handle Housing | 1 |
| 1 | 1129 790 1016 | Handle Housing | 1 |
| 19 | 1129 790 9700 | Stop Buffer | 1 |
| 14 | 1129 790 9900 | Annular Buffer | 1 |
| 17 | 1129 790 9903 | Annular Buffer | 1 |
| 17 | 1129 791 0601 | Handle Moulding | 1 |
| 13 | 1129 791 1701 | Beugelhandgreep | 1 |
| 16 | 1129 791 6100 | Screw | 1 |
| 20 | 1129 791 6101 | Kraagschroef | 1 |
| 5 | 1129 792 5500 | Bushing | 1 |
| 8 | 1129 792 9101 | Handbeschermer | 1 |
| 22 | 1129 967 1504 | Model Plate Ms 200 | 1 |
| 18 | 1130 448 1201 | Lead Retainer | 1 |
| 26 | 1137 122 6700 | High Speed Screw | 1 |
| 4 | 4116 121 5100 | Inlet Needle | 1 |
| 36 | 4132 122 6600 | Kraagschroef | 1 |
| 27 | 4229 121 2701 | Cap | 1 |
| 11 | 9022 313 0660 | Spline Screw Is-M4X12 | 1 |
| 7 | 9022 313 0680 | Spline Screw Is-M4X16 | 1 |
| 16 | 9022 341 0960 | Spline Screw Is-M5X12 | 1 |
| 26 | 9022 341 0980 | Spline Screw Is-M5X16 | 1 |
| 12 | 9022 371 0710 | Spline Screw Is-M4X20 MS200 / MS200T TS460 Disc Cutter Parts Brushcutter (FS) Parts Clearing Saw (FS) | 1 |
| 30 | 9022 371 1020 | Spline Screw Is-M5X20 | 1 |
| 35 | 9074 478 4135 | Pan Head Self-Tapping Screw Is-P5X20 | 1 |
| 21 | 9074 478 4435 | Pan Head Self-Tapping Screw Is-P6X19 | 1 |
| 14 | 9074 478 4675 | Pan Head Self-Tapping Screw Is-P6X32.5 | 1 |
| 24 | 9099 021 1760 | Self-Tapping Screw Din7971-2.9X9.5 | 1 |
| 7 | 9104 003 3004 | Self-Tapping Screw Is-P4X14 | 1 |
| 33 | 9104 003 8710 | Self-Tapping Screw Is-P4X10 | 1 |
| 9 | 9216 261 0700 | Hexagon Nut Chainsaw Parts M5 MS170 / MS170C MS180 / MS180C MS210 / MS210CMS230 / MS230C MS250 / MS25 | 1 |
| 11 | 9291 021 0121 | Washer Din125-A5,3 | 1 |
| 29 | 9331 630 0120 | Conical Spring Washer Din6796-5 | 1 |
| 4 | 9378 543 2700 | Notched Pin Din1474-5X30 | 1 |
| 8 | 9380 620 1090 | Roll Pin Iso8752-2X10-St | 1 |
| 8 | 9416 868 5631 | Hollow Rivet Din7340-Ak5.5X0.5X6.8 | 1 |
| 23 | 9463 650 0900 | Snap Ring Din73130-C9X0.8 | 1 |
| 25 | 9512 003 2030 | Needle Cage 9X12X10 | 1 |
| 18 | 9512 933 2270 | Needle Cage 10X13X13 | 1 |
| 2 | 9531 003 0105 | Roller Bearing Rh12X24.5X8.8 | 1 |
| 3 | 9640 003 1191 | Oil Seal 12X20X5 | 1 |
| 14 | 9645 948 2470 | O-Ring 23X3 | 1 |
| 9 | 9645 948 7734 | O-Ring 25X3.5 MS210 / MS210C Chainsaw Parts MS230 / MS230C MS250 / MS250C MS200 / MS200T | Stihl MS | 1 |
| 7 | 9646 945 0160 | O-Ring Din3771-S4X2 | 1 |
Chain Sprocket Cover
1 onderdelen| Pos. | Onderdeelnummer | Omschrijving | Aantal |
|---|---|---|---|
| 1 | 1129 640 1702 | Kettingwieldeksel | 1 |
Onderhoud & Slijtageonderdelen STIHL MS 200 T Familiebron gekoppeld
β’ Aanbevolen Bougie: Bosch WSR 6 F
β’ Elektrodenafstand: Niet betrouwbaar gedocumenteerd
β’ Technische kettingmaten (steek, schakeldikte, aantal aandrijfschakels) worden per uitvoering gespecificeerd in de handleiding.
β’ Zaagkettingolie: Controleer in de handleiding de aanbevolen kettingolie en viscositeit voor continue smering van blad en zaagketting.
β’ Controleer in de handleiding of op de machine zelf welk carburateurfabrikaat en revisieset op uw specifieke uitvoering zijn gemonteerd.
β’ Controleer het filtertype en de voorgeschreven onderhoudsinterval op basis van de bouwjaarrevisie en werkomstandigheden.
Belangrijk voor aankoop van onderdelen:
Controleer altijd het serienummer van uw STIHL MS 200 T op het carter of typeplaatje voordat u onderdelen bestelt. Bij productierevisies en M-Tronic generatiewijzigingen kunnen carteronderdelen en ontstekingsmodules verschillen.